Single hung
Double hung
Horizontal roller
Casement
Bay & bow
Sliding glass doors
Entry doors
Impact garage doors
PGT
CGIFree in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Get your free estimateTherma-Tru Custom & Geometric Windows in Paradise: What to Know First
We provide independent Therma-Tru custom and geometric window service in Paradise, and most jobs run about three to six weeks from written estimate to final inspection – longer only when a shaped or oversized unit has to be built to order. Pricing is upfront and line-itemed before anyone touches your home, with no change orders once the work starts. This page is for Paradise homeowners who already own Therma-Tru windows or a Therma-Tru entry system and need custom impact windows, geometric and shaped windows, arched and curved units, or oversized openings serviced, matched, or replaced correctly.
Call (833) 958-8388 for a free estimate. A real person answers, day or night.
How Therma-Tru Products Fail – and How We Fix Them
Therma-Tru is best known for entry doors and door systems, and the shaped and oversized lites that sit inside or beside those systems are where most Paradise calls start. What follows are the failures our technicians see most on Therma-Tru work in this valley, and what we actually do about each.
- Failed seals and fogged insulated glass units on shaped lites. Arched and radius units on Therma-Tru door systems use curved insulating glass, and the seal on a curved unit takes more stress than a flat one as it heats and cools. When the perimeter seal lets go, you get haze between the panes that no amount of cleaning touches. We confirm it’s seal failure rather than surface film, then order a replacement lite built to the original radius and template rather than a generic flat unit forced into a curve.
- Sun-baked door slabs and sidelites on west and south elevations. Paradise sits at high desert elevation with intense summer UV, and a Therma-Tru fiberglass or steel slab facing west can chalk, fade, or lift at the finish long before the core fails. On geometric sidelites and transoms around that door, the same sun degrades glazing tapes and perimeter seals. We assess the slab and the glass separately, because replacing a sound slab to fix failed glazing is money thrown away.
- Out-of-square openings after a shaped unit is removed and reset. Geometric windows have no forgiveness in the frame – a radius unit that goes back into an opening that’s shifted a quarter inch will bind, leak, or crack at the curve. This shows up after a prior repair, a stucco patch, or settling. Our technicians measure the opening in multiple planes before the new unit is set, and shim and square it before sealing.
- Aftermarket hardware and thresholds on Therma-Tru door systems. When an owner has had a multi-point lock, threshold, or hinge replaced with a non-OEM part, the slab can shift in the frame and the adjacent shaped lite takes the stress. We identify the actual Therma-Tru system first, then decide whether an OEM replacement part is the right call or whether a quality aftermarket component will hold – and we tell you which and why before ordering.
- Oversized openings that were never engineered for the glass. Large Therma-Tru units and oversized openings in Paradise homes sometimes carry heavier glass than the original header or framing was built for. We check the rough opening and header before we quote a replacement, because a beautiful new unit in an under-built opening will fail again. If framing needs work, it’s in the written estimate, not a surprise mid-job.
One thing Therma-Tru’s own materials won’t tell you: in Paradise, the combination of high UV and dry air means perimeter sealant on shaped units dries and pulls faster than in coastal or humid climates, so we spec a sealant rated for high-UV desert exposure rather than a standard interior-grade product. That single choice is often the difference between a lite that lasts and one that’s fogged again in a few summers.
Styles & brands we work with
- Single hung
- Double hung
- Horizontal roller
- Casement
- Bay & bow
- Sliding glass doors
- Entry doors
- Impact garage doors
- PGT
- CGI
Our Therma-Tru Custom & Geometric Windows Process
- 1
Diagnose the actual system. We identify which Therma-Tru door system or window unit you have, photograph the failure, and measure every plane of the opening. No guessing from a photo on a phone.
- 2
Quote it in writing, line by line. Glass, frame work, hardware, sealant, and labor are each itemized. You see the OEM-versus-aftermarket decision and what each costs before anything is ordered.
- 3
Order the right unit. Custom and geometric glass is built to template and radius, not pulled off a shelf. We confirm lead time in writing so you’re not waiting blind.
- 4
Install with the opening squared first. Header and rough opening are checked and corrected before the new unit is set. Shaped units get set, shimmed, and verified square before sealing.
- 5
Test and seal for desert conditions. We check operation, latch, and drainage, then seal with a high-UV-rated product suited to Paradise sun.
- 6
Walk it with you and back it with the 36500-Day Done Right Promise. If it’s not done right, we make it right – period. You get the cleanup and the walkthrough before we call the job closed.
See the difference
Before
After
Before
After
Before
AfterWhat Therma-Tru Custom & Geometric Windows Costs in Paradise
These are typical ranges for Therma-Tru custom and geometric work in the Paradise area. Every job is quoted in writing before work begins, and the ranges below are a starting point, not a final number.
| Job | Typical Range |
|---|---|
| Replacement shaped or radius glass lite (single) | $450 – $1,200 |
| Arched or curved custom unit, supplied and installed | $1,400 – $3,800 |
| Oversized opening rework and re-set | $900 – $2,600 |
| Therma-Tru entry system service and hardware | $250 – $850 |
| Custom impact window, per unit | $600 – $2,200 |
What moves the price: the radius or shape complexity, whether the opening needs framing correction, OEM versus quality aftermarket parts, and lead time on a built-to-order unit. Call (833) 958-8388 for an exact quote – estimates are free, and a second opinion on another written estimate costs you nothing.
Why Paradise Homeowners Call Winslow Windows & Doors Paradise for Therma-Tru Work
We’re locally owned and owner-operated, and Ed Winslow’s name is on the door and on every job we do. Every technician is background-checked and arrives in uniform, so you know exactly who is at your door before the truck pulls up. Calls are answered by a live person 24 hours a day, seven days a week – no voicemail loops and no next-business-day callbacks. Our technicians have up to 15 years of experience, and they know how Therma-Tru systems are built and where they fail in Paradise heat.
As an independent Therma-Tru service provider, we’re not affiliated with or authorized by Therma-Tru – we work on their products because they’re good products and our customers own them. We also install and service PGT, CGI, CWS, and ES Windows, so if a Therma-Tru unit is no longer the right answer for your opening, we’ll tell you and show you the alternatives. Upfront pricing, no trip charge inside the home county, $40 off any repair over $200, and 10% off for seniors and veterans – these are permanent, not a promotion.
FAQs
Servicing a Therma-Tru window doesn’t void the warranty as long as the work is done correctly and with appropriate parts. Our technicians follow warranty-safe practices – proper parts, correct installation, and documentation of what was done – so your coverage stays intact. Call (833) 958-8388 to schedule your free estimate.
Yes, OEM parts and built-to-template glass for Therma-Tru geometric and arched units are available, though lead times vary. When a quality aftermarket part is the better value and will hold up, we’ll tell you why before we order. Call (833) 958-8388 for an exact quote on your unit.
Repair usually wins when the frame and opening are sound and only the glass or hardware has failed. Replacement makes more sense when the opening itself has shifted or the unit is beyond a warranty-safe fix. We give you both numbers so you can decide. Call (833) 958-8388 for a free estimate.
Most jobs run about three to six weeks from estimate to final walkthrough, with custom and built-to-order shaped units on the longer end. We put the lead time in writing before you commit. Call (833) 958-8388 for your free estimate.
Yes – when a permit is required for window or door work, we handle pulling it and getting it inspected before the job is closed out. Your written estimate notes what’s needed. Call (833) 958-8388 to get started.
Ready for a straight answer on your Therma-Tru custom or geometric window? Call Winslow Windows & Doors Paradise at (833) 958-8388 for a free estimate. A live person answers around the clock, the pricing is upfront and line-itemed, and the 36500-Day Done Right Promise stands behind every job. We’re the one down the road.
Written by the team at Winslow Windows & Doors Paradise, serving Paradise and nearby areas.